CMC
is macromolecule compound with multichain, and the linear chain will open,
spread, interact and form the network collide after the water swelling.
Meanwhile, the macromolecule chain with oxhydryl has hydration with water and
twine with each other, and then increase the water phase viscosity. It has the
excellent compatibility in water or in organic solvent, as well as the pigment.
It used as thickener, dispersant and stabilizer in coating industry.
1. Application in regular coating
CMC’ s oxhydryl macromolecule chain has hydration with water and twine with
each other, and then increase the water phase viscosity. It has the excellent
compatibility in water or in organic solvent, as well as the pigment. It also
can greatly improve the viscosity and rheology, and it used as thickener,
dispersant and stabilizer in coating industry. CMC which is applied in
water-solube coating will show the effect as follows:
*Good water resistance and filming durability;
*High fullness of filming, well-distributed of filming, and highlight
acquirable,
*As the stabilizer, it can prevent the paint-coat from being apart due to the
abrupt change of the temperature ;
*As the protective colloid, it can maintain the stability of coating system in
the wider range of pH value;
*As the thickener, it can make the coat well-distributed, and achieve to the
expected viscosity for storage and construction, and avoid the serious
stratification during the period of storage.
*Enhance the coat leveling property, anti splash and anti sagging, so that
improve the construction workability;
*Make the additives like pigment and filler be dispersed in the coat and the
coat will show the excellent effect of pigment adhesion.
2. Application in latex paint
Latex paint mainly composed of polymer water dispersion and pigment water
dispersion. Its viscosity has the influence on settleability, brushability,
roll coating, fullness of film, levelling property and the sagging property on
the film vertical surface, so it will often adjust the viscosity and rheology
of latex paint. While CMC has the advantages of good rheology, small resistance
of brush coating, easy for construction, and thus it used as the stabilizer,
thickener and water retention agent.
*Good thickening effect, high efficiency for latex paint thickening
*Be with stability property., and make the paint a certain viscosity with no
residue in storage;
*Make the moisture permeate the porous substrate slowly, and maintain the water
when the latex content is high;
*Less limitation on paint formula, small effect by collide type, dispersant and
surface active agent;
*Coating finishes, and the water action with the CMC will terminate. Regain the
viscosity and avoid sagging.
3. Application in casting paint
CMC is macromolecule compound with multichain, and the linear chain will open,
spread, interact and form the network collide after the water swelling. CMC can
interact with the sodium base bentonite, and it not only improve the suspending
power of sodium base bentonite, but also dramatically reduce the volume of the
sediment agglomeration, furthermore, it prevents the fire intolerant aggregate
from sinking. Thus, it always used as to enhance the suspensibility rate of the
casting paint, and improve the paint viscosity.
*Excellent water-solube viscosity increasing, and improve the coating viscosity
and rheology;
*Good solubility and dispersion, making the solids suspend in the carrier
liquid;
*Impel the fire intolerant powder suspend and avoid settling, layering and the
carrier liquid excessive penetration into the molding material;
*Promote the spreading and covering power of paint, and enhance its brushing
property and leveling property;
*The powder bonds with each other after dried, and adheres firmly on the inside
and outside surface
4. Special products for coating grade
HPCT2000 has a good ability to resist divalent ions and the glue with HPCT2000
can enhance the stability of white cement and not easy to be mildewed.
Property
Type
|
Viscosity, 25oC
Brookfield, CPS
|
Application
|
T6
|
2% 400-800
|
Used
as a protective colloid in coating material
|
T8
|
2% 800-2000
|
T10
|
1% 300-500
|
T30
|
1% 2000-5000
|
ST
|
1% 2000-5000
|
Coating fields
where there are certain requirements on solution rate
|